- SAITEK X52 PRO MODS INSTALL
- SAITEK X52 PRO MODS DRIVER
- SAITEK X52 PRO MODS FULL
- SAITEK X52 PRO MODS PRO
I found two identical rubber bands, rather thick and short, and attached one around the horns and front vertical tab, and the other around the horns and rear vertical tab. I removed the two springs that control the pitch axis resistance and removed the arms to which they were attached to, saving them in case I wanted to go back to the original configuration. Though I am not a fan of using rubber bands to fix issues, in this case the application is a good place to use them. This reminded me of a video of improving the CH yoke by attaching rubber bands to these horns. I noticed that there are two plastic "horns" on the middle yoke shaft, and equidistant vertical tabs a few inches forward and back of it. I thought that there must be some simple solution to this problem. So today I decided to open it up for the 101 time. After trying some of these suggestions, I still was not happy with the performance of this product. Still others have cut the bushings and changed lubricants. There have been a number of "improvements" that others have done to counter this issue, such as removing one of the pitch springs, replacing them with other springs, or even one person who re-engineered the product to behave like the CH yoke with side springs which provide both pitch and roll resistance. No other tricks.Many people complain about the bothersome detent in the pitch axis of this otherwise good product. I use the X52 machine to test Community items, or items I find in the Forums, also to check in staff that works in one and not on the other one, both computers are the same hardware and power, and that is all about it. I have a different machine with all the peripherals (Saitek panels, Alpha, Bravo units, MFG pedals, etc.) but I have never used the X52 in it.
SAITEK X52 PRO MODS FULL
The connections between the Joystick and the throttle sometimes fails, it is the nature of the connection, not strong, push on the terminals inward to get a full connection. My MFD always illuminates, as soon I connect the USB from the Hub to the computer. It was from here that I created profiles for MSFS and X-Plane, so I have to remember when to use one or the other, but you see the icon in the Task Bar of all the software loaded, you will see the small icon for the Joystick that allows you to choose profile.
SAITEK X52 PRO MODS INSTALL
You have to install the Programming Software as well which loads when booting your PC. I did not use any buttons or wheels in the MFD, and if they where assigned by default to anything I removed it. Like I said I installed the driver, once recognized by MSFS, I assigned the proper buttons and axis, save it. Also the quality of my X52 is somewhat better than what Logitech has been selling for what I read on the subject, finally I don’t believe in magic. The Programing Software came with my original X52 that I purchased from Saitek a few years back, the one in the Logitech site is the same one. I don’t have any Saitek Panels of any kind connected to this machine. I also use the Programing Software for the X52 and I have 2 profiles, one for MSFS, and another for X-Plane, this software loads at booting time and I get an icon in the starting tab from where I can choose the profile I need. I may add that it works the same way in X-Plane 11. It also flashes the name of any button you use in a separate line. I made sure I did not assign any of the buttons or rotating wheels in the MFD to any commands, my MFD illuminates when computer is on and shows local or UTC time, it also works like a stopwatch, and shows the Com 1,2, Nav 1,2 frequencies when I fly.
SAITEK X52 PRO MODS DRIVER
I installed the X52 with the driver from Logitech.
SAITEK X52 PRO MODS PRO
In one of my computers I have the X52 Pro connected to a USB Hub, a switch box I made also connected to the Hub.
0 kommentar(er)
